Tindie
MMM999
Micro SD card reader module for Arduino
$4.90
Soil Hygrometer Humidity Detection Sensor
$5.00
Microcontroller Board For Arduino
$15.00
1.8 In TFT LCD Display Module
$9.99
ARM Cortex-M3 STM32F103C8T6 STM32 Minimum System Development Board With Mini USB
$12.00
Arduino Compatible Esplora Game Programming Board
$35.00
12V Power-ON Delay Relay Circuit
$7.80
Microwave Doppler Wireless Radar Sensor
$7.20
2.4G Wireless Transceiver Module + Antenna
$7.00
RFID Card Reader Induction Module
$7.00
DC 7V-24V To DC 5V 3A USB Output Converter Step Down Module ...
$7.50
Dot Matrix LED Display Kit For Arduino
$6.00
About
About shipping:
- Economy shipping: (If you have urgent needs, we do not recommend using this shipping method)
This is a free delivery service, can't provide tracking number, please give it more time to receive it. If you can't accept, please choose "Standard shipping" or "Expedited shipping".
Note: If you purchase over $38, we will automatically be upgraded to the standard shipping. \o/
- Standard shipping:
This is a charge a small postage service that provides tracking number. If you need to receive it faster, please choose "Expedited shipping" or contact us.
- Expedited shipping:
This is an international post offices fast shipping method (Express Mail Service, EMS), most can be received within 7 business days, there may be delays in customs. If you need to receive it faster, please contact us.
Reviews
Tim | Oct. 4, 2018
Good products
For Arduino Compatible Nano Size Board
Trevor | Aug. 21, 2018
The best little digital oscilloscope available.
For Original JYE Tech DSO-SHELL DSO150 15001K DIY
The display of frequency, voltage (P-P and RMS) and duty cycle is great for Arduino or ESP8266 debugging (particularly PWM outputs) and the triggering is stable. A 10Xprobe extends them for mains-level or Vacuum tube applications, so get one of those to complete your kit.
This last unit arrived two weeks earlier than expected - a definite plus - I was keen to get it up and running.
Philippe | April 16, 2018
the device works
For 12V-24V infrared PIR Motion Sensor Switch Controll
Peter | Feb. 9, 2018
Nice little board
* A reset switch
* A jumper to disconnect the EEPROM, in case you screw up programming it
* Every single available pin except WAKEUP, not just GPIOs, is broken out to the headers, even SDA/SCL, making it trivial to e.g. add a larger EEPROM
* A power switch is a nice touch given the 3V3 power available on the headers
* Four mounting holes are nice too
Regarding the following:
> With the board firmware can be achieved through the core function of the logic analyzer.
This means that the board is programmed to appear as a device 0925:3881 Lakeview Research Saleae Logic using the on-board EEPROM. There is no actual firmware inside, it uses a "C0 load". It will work as a logic analyzer with any supporting software (e.g. PulseView), however it is not ethical to ship a device using Saleae USB VID/PID. Instead, Sigrok's USB VID/PID, 1D50:608D, should be used, which will also enable using all 16 possible channels in the logic analyzer, not just 8 with the default VID/PID pair. See https://www.sigrok.org/blog/sigrok-firmware-fx2lafw-013-released and https://sigrok.org/wiki/Fx2lafw for details.
The only other downside is the lack of schematic.
Mark | Feb. 2, 2018
Have not received Item, No communication from Seller.
For Nano V3.0 ATmega328P-AU Microcontroller Board
Response from MMM999 | Feb. 2, 2018
i didn't receive your message
sorry
can u send me the order id to checj the state?
thanks
