A USB-C Power Delivery Sink based on the Cypress CYPD3177 USB PD ControllerDesigned by Pier 42 in Canada
Due to the current global situation, I cannot ship to countries where Canada Post has suspended service. I recommend shipping tracked and parcels to add security for the buyer and seller.
NEW Rev 4 now available. Important improvement with a 2nd switch to select the current! Blue PCB again and black screw terminal and new FETs as power switches. The new FETs have a Rds_on of only 7....Read More…
NEW Rev 4 now available. Important improvement with a 2nd switch to select the current! Blue PCB again and black screw terminal and new FETs as power switches. The new FETs have a Rds_on of only 7.3 mOhm (measured), which cuts the dissipation almost in half and keeps the board cooler, even with 5 A current draw.
USB-C PD offers the option to negotiate power delivery from a compatible power supply. The USB-C PD-Sink plays the role of a sink device, enabling any device to be powered from a USB-PB power supply. Any type of power connector can be attached through a 2-pin screw terminal or directly soldered into the PCB for a lower profile. The voltage can be set to 5V, 9V, 12V, or 20V and current can be set to 1A, 2A, 3A, or 5A. BCR stands for Barrel Connector Replacement, the term is invented by Cypress, the manufacturer of the controller chip in use here. This board has the goal to replace random power adapters with a standardized way to use a USB-C power delivery (USB PD) adapter instead. For regular operation, no programming or software configuration is involved with this design. All options are set through the switches or resistor values. If needed an I2C interface to a microcontroller is available, to access status and control registers. This part of the board is separated through a break-off tab (mouse bites) and can be snapped off. I made the conscious design decision to not add a USB-A connector option at the output end. I did not want to build a device, that is capable of putting more than 5V on the VBUS pin of a regular USB cable and potentially destroy the device that is plugged in. A heatshrink tube is provided to protect the board in a permanent installation.
A set of 5mm x 2.1mm barrel jack+plug and a 2-pin 0.1" female header are available to add on. The barrel jack is a generic type with screw terminals for wires. The pin header has a current limit of 3 Amps and can be used to power a Raspberry Pi through the HAT connector.
This is a set and forget device. Set your current and voltage needs before plugging the device to your USB-PD source and enjoy the power at the output. This is not a power supply to change voltage and current during operation.
I wanted to provide small form factor, easy to use, no software involved solution.
The USB-C PD Sink can be built in-line with an existing power cable to make almost every device USB-C compatible.
No country selected, please select your country to see shipping options.
No rates are available for shipping to .
Enter your email address if you'd like to be notified when USB-C PD Sink can be shipped to you:
Thanks! We'll let you know when the seller adds shipping rates for your country.
|Shipping Rate||Tracked||Ships From||First Item||Additional Items|
Due to the current global situation, I cannot ship to countries where Canada Post has suspended service. Also I recommend shipping tracked and insured parcels to add some security for the buyer and seller. Please contact me before ordering and I might be able to get a better rate for your destination country. Thank you very much for your understanding and be well. - Pier42.
Kristian | Jan. 24, 2021
Alexis | Jan. 4, 2021
Antonin | Nov. 19, 2020
David | Oct. 31, 2020
Patrick | Aug. 19, 2020
Peter | Feb. 14, 2020
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!