Tindie
Makertum MK1 – 230/110 V~ Heated Bed Full Kit+SSR
$49.00
Free shipping is available to United States!
Sold out since Jul 29, 2017
Add to Wishlist
On Wishlist
On 3 Wishlists
makertum posted:
We're on vacation from May 1st, 2017 to June 7, 2017. Please order before or after :)
The Makertum MK1 is a mains voltage (230/110 V~) heated bed for 3D printers with 500 W of heat output, 2min heatup time and thermal fuse.
The Makertum MK1 is a mains voltage heated bed for 3D printers with dual voltage support for both 230 V~ and 110 V~. It features a power output of 500 W, which ensures a fast heat up time of 2 minutes to 110 °C, a power indicator LED and an onboard thermal fuse. Here you can order one kit from the pre-production run.
About the pre-production
- Free worldwide* shipping
- No crowdfunding, no preorder. Kits are packed, you order, we ship.
- If anything goes wrong, or you make up your mind, you will get a friggin' refund, of course.
- The preorder boards resemble the final product, but in a way they are not: Minor changes and tweaks may still be made on the final version.
- Follow the project updates here: hackaday.io
Kit Content
- Makertum MK1 Pre-production PCB
- Thermal fuse
- Overcurrent fuse and fuse holder
- Polycarbonate LED cover
- SMD LEDs and resistor
- 2m high-temperature silicone wire
- Cable lugs and ferrules
- Luster terminal
- Screws, nuts and washers
- Shrinking tubes
- Solid State Relay (SSR)
Documentation
Schematics and BOM can be found on GitHub, extensive assembly instructions are maintained on hackaday.io.
Features
This implementation comes with a few more extra features:
- super fast heatup time (about 10 times faster than the common MK2)
- 230 and 110 V~ support
- power indicator LED covered by tough transparent polycarbonate
- no thermal breathing / flex due to double sided layout
- compatible with RepRap MK hole spacing of 209 mm center-to-center
- extra mounting holes for three point leveling
Required skills
This is a kit. Don't panic, we got you covered with extensive instructions. Still, you'll need a few basic skills:
- crimping (0.75 mm cable lugs and ferrules)
- soldering down to 0603 SMD (can be done with tweezers and a fine tip)
- mains voltage wiring, installation, and safety precautions
Safety
We did everything to make this the safest heated bed available:
- fully insulated screw terminals
- thermal fuse prevents overheating
- current fuse prevents overcurrent
- made from temperature resistant FR4
- thorough stress testing on every manufactured batch
Specs
The exact power output may vary due to manufacturing tolerances. The following specs represent a statistical average of the batch we're currently shipping.
| Key (is key) | Value (this text makes the table a bit wider) |
|---|---|
| Power Output | 540 W (230 V~) or 490 W (110 V~) (+/- 25%) |
| Operating Voltage | 230 V~ (110 V~ over center tap) |
| Resistance: | 96 Ω (+/- 25%) |
| Trace-Length | 400 x 200 mm = 80,000 mm |
| Copper thickness (on PCB) | 1oz aka 1.37 mil aka 35 µm |
| Trace width | 0.47 mm |
| Dimensions (WxHxT) | 214x214x1.6 mm (w/o screw terminals) 214x224x1.6 mm (w. screw terminals) |
| Mounting Holes / Compatibility | 209 mm center-to-center (RepRap compatible) + 3-point leveling |
Legal Liability Disclaimer
By purchasing this kit, you agree to the following terms:
- You have enough experience in mains voltage electronics and mains voltage installations to manage the installation and operation of the provided heated bed.
- The safety of the provided heated bed depends on how you install it into your applications. Dangerous malfunctions can still occur. *The provided heated bed may not be operated without sufficient safety precautions and professional supervision.
- You will take all necessary mains voltage related safety precautions and fire protection precautions when operating the provided heated bed.
- You will take full responsibility for your actions and their consequences when operating the provided heated bed.
- You relief Makertum OÜ and staff thereof of all liability for the provided heated bed, including but not restricted to the occurance damage of property, harm to human or animal, or whatsoever.
Additional Information
*We currently can't ship to German customers. Sorry, for the inconvenience. Feel free to contact us if you live in Germany and really need one.
Awesome product. Must buy.
Oct. 20, 2016 - Makertum MK1 – 230/110 V~ Heated Bed Full Kit+SSR
I've tested this with a few prints so far and it is amazing. Takes my bed a little over a minute now to heat up to 100 deg C! Before I had a 12V heat bed that took 20+ minutes to heat up to 100 deg C and could barely hold the temperature. If you have a 12V heat bed currently throw it out and buy this!
* 4 stars for shipping because of a lack of a tracking number but this is just a preference and in no way affects how great the product is. It just meant that I got a surprise at my doorstep after a week or so :)
* Defaulted to 5 stars for communication but there was no need to contact the maker.
* 4 stars for documentation - it is complete and adequate to do the job though it could be a bit more polished
* 4 stars for shipping because of a lack of a tracking number but this is just a preference and in no way affects how great the product is. It just meant that I got a surprise at my doorstep after a week or so :)
* Defaulted to 5 stars for communication but there was no need to contact the maker.
* 4 stars for documentation - it is complete and adequate to do the job though it could be a bit more polished
I'm blown away!
Oct. 9, 2016 - Makertum MK1 – 230/110 V~ Heated Bed Full Kit+SSR
So, I ordered this as sort of a test of Tindie (my first purchase) as well as supporting a Hackaday.io project. Now after running with the product installed on my printer for over a week, I've become forced to write a glowing review. I normally don't take time from my busy life to review things unless they're horrendous or amazing. This is definitely one of the latter.
The things that stand out to me are:
1. Documentation - the writeup on Hackaday.io is detailed and documented well with pictures. The only thing I would change about it is to add a diagram showing how to connect to your 3d printer's controller - but really it isn't any different than your old heated bed. Also, with the SSR chosen, you can do PID just like the old DC heated bed you probably used.
2. Safety - the little things like including a cover for over the SMD LEDs and the thermal fuse, copious heat shrink, in-line fuse, etc. These all add up to a well thought-out product with safety not taking a back seat to convenience or cost.
3. Cost - what you get for what you pay is well worth it. The SSR itself is not cheap and is a good brand. Nothing was sacrificed in the name of making money - rather I'm actually very surprised that this product can sell for what it is and the maker actually feels it is worth his time to produce!
4. Community - on top of it all, I would have bought it to support Hackaday and Tindie and the maker - if for no other reason than to help support another maker and not to support some large corp.
Thank you! I hope you're still selling these when I make my next printer and need another! Consider creating a circular heated bed as well for the delta people out there? That might be my next build.. :-)
The things that stand out to me are:
1. Documentation - the writeup on Hackaday.io is detailed and documented well with pictures. The only thing I would change about it is to add a diagram showing how to connect to your 3d printer's controller - but really it isn't any different than your old heated bed. Also, with the SSR chosen, you can do PID just like the old DC heated bed you probably used.
2. Safety - the little things like including a cover for over the SMD LEDs and the thermal fuse, copious heat shrink, in-line fuse, etc. These all add up to a well thought-out product with safety not taking a back seat to convenience or cost.
3. Cost - what you get for what you pay is well worth it. The SSR itself is not cheap and is a good brand. Nothing was sacrificed in the name of making money - rather I'm actually very surprised that this product can sell for what it is and the maker actually feels it is worth his time to produce!
4. Community - on top of it all, I would have bought it to support Hackaday and Tindie and the maker - if for no other reason than to help support another maker and not to support some large corp.
Thank you! I hope you're still selling these when I make my next printer and need another! Consider creating a circular heated bed as well for the delta people out there? That might be my next build.. :-)
Rates to United States
| Shipping Rate | First item | Additional items |
|---|---|---|
|
Free Shipping: Wordwide Standard Shipping
|
$0.00 | $0.00 |
|
DHL: Wordwide Express (Premium)
|
$16.20 | $0.00 |
Store Owner
- Makertum Oü
- 17 orders / 2 reviews
- Since Jul 27, 2016
- Usually ships within 1 day
- Berlin, Germany
- Custom Work
