Purchase all items from raw PCB to complete Smart Home KitDesigned by JARViE in United States of America
Product Description The JARViE PLM Demo Board offers users a simple and low-cost entry point into learning about Smart Home technology. Couple this modem with a microcontroller to bidirectionally ...Read More…
The JARViE PLM Demo Board offers users a simple and low-cost entry point into learning about Smart Home technology. Couple this modem with a microcontroller to bidirectionally communicate with other devices or systems over AC or DC power lines. Applications include lighting control, home appliance control, energy/heating control and up to 3,000 feet data transmission home power networks.
The demo board highlights the NXP TDA5051A home automation modem. The TDA5051A is an amplitude shift key (ASK) power line modem that operates up to 1200 bits per second (bps) from a single +5VDC supply. The receiver portion of the modem employs automatic gain control (AGC) at its input and the transmitter has output power overload protection. An 8-bit A-to-D converter and a narrow digital filter follow the AGC stage in the receiver. The TDA5051A power line modem application solution is compliant with US FCC (Federal Communication Commission), Industry Canada, Japan MPT, and European CENELEC EN50065-1 regulations for signaling in the 125 kHz to 140 kHz and the 95 kHz to 125 kHz frequency bands.
The JARViE PLM can communicate over +48 VDC max or up to 240 VAC power lines. The figure below diagrams a home application. The master and slave devices employ an MCU and the JARViE PLM. During a data transmission event (device master sending out data to slave devices), the MCU sends the data to be transmitted to the PLM's TDA5051A via a UART interface. After internal processing, the PLM broadcasts the data over the power line to all slave devices using a modulated carrier wave. During a data reception event (slave device receiving data from master), the PLM's TDA5051A converts the carrier wave into digital data. The digital data is fed into the MCU's UART interface for interpretation.
The complete demo kit provides everything needed to quickly get started with communicating over AC or DC power lines. There's a huge value add that comes with purchasing the kit; all the hardware is proven and software examples are available on GitHub. This gets the developer learning PLM technology on day one and NOT spending days specifying and purchasing hardware and or developing firmware.
All info (product documentation, firmware, etc.) for quickly getting started is on the device GitHub page.
The non-insulated high voltages that are present when operating this product, constitute a risk of electric shock, personal injury, death and/or ignition of fire. This product is intended for evaluation purposes only. It shall be operated in a designated test area by personnel that is qualified according to local requirements and labor laws to work with non-insulated mains voltages and high-voltage circuits. This product shall never be operated unattended.
The board needs to be connected to mains voltage. Touching the reference board during operation must be avoided at all times. An isolated housing is obligatory when used in uncontrolled, non-laboratory environments. This isolation is not according to any regulated norm. Galvanic isolation of the mains phase using a variable transformer is always recommended.
JARViE is NOT liable for any mishaps that occur while using this board. User must consider and take proper safety precautions while working with high-voltages.
The following image shows the DATA_IN to Tx carrier output delay. The blue trace is a 1 kHz square wave driving the PLM's TDA5051A modem DATA_IN input. The yellow trace is the modulated ASK carrier wave transmitted to all PLMs on the power line network. The capture shows that there is approximately a 170 microsecond delay between setting the DATA_IN input and Tx carrier wave generation.
The following image shows the Rx carrier input to DATA_OUT output delay. The blue trace is the modulated ASK signal received through the AC inputs on the JARViE PLM. The yellow trace is the digital TDA5051A DATA_OUT signal that can be interpreted with an MCU or equivalent UART compliant device. The capture shows that there is approximately a 180 microsecond delay between Rx carrier wave reception and the DATA_OUT output.
The main purpose of the PLM zero cross detection circuitry (ZCD) is to provide a method to synchronize devices to one another. The intent is to not have to share a clock between devices that are meters away. The output of the ZCD goes from 0 to +5V making it compatible with MCUs. By pairing the PLM with an MCU, the ZCD output can be used to trigger event timers, create task schedulers within a PLM network and or send messages when noise on the power line is smallest for best communication results (zero crossing point). The ZCD can also be used to measure the frequency of the AC power line.
This product was made to provide a reliable and low-cost solution for leaping into Smart Home and Internet of Things (IOT) applications quickly.
The PLM board + a microcontroller enables devices to communicate over meters of 240/120 VAC or +48V max DC power lines removing the need to have devices closely tethered together with more than two wires. Devices being able to communicate over meters of AC or DC power line enables one to develop a mesh network of two or more distributed devices, each having unique functions. Devices that potentially allow one to close your garage, turn-off a downstairs TV or monitor the power consumption of home appliances while lying in bed is a possibility.
|Shipping Rate||Ships From||First item||Additional items|
United States Postal Service: Standard Ground Rate
United States Postal Service: Priority Mail with tracking
United States Postal Service: First-Class Package International Service
Pflugerville, TX, United States of America
Ships from United States of America.
Usually ships within 3 days
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!