Nordic nRF52832 BT5 Bluetooth BLE Module Pre-Certified BQB/FCC/IC/CE/Telec/KC/SRRC/NCCSold By Nordic Solution Bluetooth Module
All modules are Bluetooth BQB tested, QDID granted and FCC/IC/CE/Telec/NCC/SRRC pre-certified. The best solution to lower down your BOM cost and speed up Time-To-Market efficiency.
Raytac's Modules 100% Made In Taiwan; No worry about the Trade War Risk With China! MDBT42Q-U512KV2 (nRF52832 Build Code#E SoC) Raytac’s MDBT42Q & MDBT42Q-P is a BT5.0 & BT4.2 stack (Bluetooth ...Read More…
Raytac's Modules 100% Made In Taiwan; No worry about the Trade War Risk With China!
MDBT42Q-U512KV2 (nRF52832 Build Code#E SoC) Raytac’s MDBT42Q & MDBT42Q-P is a BT5.0 & BT4.2 stack (Bluetooth low energy or BLE) module designed based on Nordic nRF52832 SoC solution, which incorporates: GPIO, SPI, UART, I2C, I2S, PWM and ADC interfaces for connecting peripherals and sensors.
MDBT42Q-U512KV2 is the module designed based on u.FL connector which is able to connect to external antenna which is the optimized solution for those design pursue a better RF efficiency.
Bluetooth: BT5.1 & BT5 & BT4.2
(Regulation is tested under Raytac's selected antenna)
About The Module:
Dual Transmission mode of BLE & 2.4Ghz RF upon customer preference.
Compact size with (L) 13.8 x (W) 8.8 x (H) 2.2 mm.
Low power requirements, ultra-low peak, average and idle mode power consumption.
Be compatible with a large installed base of mobile phones, tablets and computers.
‧Multi-protocol 2.4GHz radio
‧32-bit ARM Cortex – M4F processor
‧512KB flash programmed memory and 64KB RAM
‧Software stacks available as downloads
‧Application development independent from protocol stack
‧On-air compatible with nRF51, nRF24AP and nRF24L series
‧Programmable output power from +4dBm to -20dBm
‧RAM mapped FIFOs using EasyDMA
‧Dynamic on-air payload length up to 256 bytes ‧Flexible and configurable 32 pin GPIO
‧Programmable peripheral interface - PPI
‧Simple ON / OFF global power mode
‧Full set of digital interface all with Easy DMA including:
‧3 x Hardware SPI master ; 3 x Hardware SPI slave
‧2 x two-wire master ; 2 x two-wire slave
‧1 x UART (CTS / RTS)
‧PDM for digital microphone
‧I2S for audio
‧12-bit / 200KSPS ADC
‧128-bit AES ECB / CCM / AAR co-processor
‧Lowe cost external crystal 32MHz ± 40ppm for Bluetooth ; ± 50ppm for ANT Plus
‧Lowe power 32MHz crystal and RC oscillators
‧Wide supply voltage range 1.7V to 3.6V
‧On-chip DC/DC buck converter
‧Individual power management for all peripherals
‧5 x 32-bit
‧3 x 24-bit RTC
‧NFC-A tag interface for OOB pairing
|Shipping Rate||Ships From||First item||Additional items|
DHL: USA Ground Rate
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!