The Typical Problem Faced by Beginners in Learning Electronics on Raspberry Pi

• Raspberry Pi aims to bring the power of computing and digital making to the masses. It is being used by many educators, makers, and also engineers. Yet, if you are a newbie learning electronics, you might face some of these constrains:
• Hard to get started without additional devices (monitor, keyboard and mouse). Beginners will either need to use additional devices or follow many steps just to get started. This may confuse them. For techies that wants to know why, this is because it lacks an on-board USB to UART communication for your computer to get the IP address for SSH (headless), or to kick start configuration directly.
• Hard to get started with the electronics. It doesn't come with any inputs or outputs, you will need to connect additional accessories to use it. Most beginners do not have basic knowledge in electronics. They will have problem to understand the circuit diagram and connections needed when they first started learning. They will spend a substantial amount of time just to connect the wires and troubleshoot the connections.
• Hard to troubleshoot the GPIO. With just the raspberry pi, beginners face a common problem when learning electronics- difficulty in troubleshooting their circuit. This is because when it doesn't work, we do not know whether the problem is due to wire connection or coding.
• Access to GPIO is kind of difficult. There is no label on the pins, you need to search online to get the designated pin and know which pin to connect. For beginners, this definitely will make it harder for them to make the connection correctly.
• No easy way to properly shutdown using a switch. There is no programmable push button to enable proper shutdown through hardware. If the beginner turn off the power without properly shutting it down, the raspberry pi may not work the next time.

Introducing Our Solution: Maker pHAT Maker pHAT solves all these. It is designed to:

• Simplify to get started with Raspberry Pi without additional monitor, keyboard or mouse (Headless). Go headless with a few simple steps as it enables user to remote access Raspberry Pi through serial.
• Simplify learning electronics. Beginners can skip the hassle of constructing the basic electronic circuit which is boring and time consuming. Although it is equally important for them to learn about basic electronics, it can always come later after they have experienced how easy it is to create awesome project. Start with fun and excitement. Start coding right away and see your board lights up and plays sound with the press of a button. It comes with on board LEDs, push buttons and buzzer to easily learn how to control input and output. No messy wiring needed and no additional components needed.
• Simplify troubleshooting and prototyping. Not only do the onboard LEDs work as outputs, they can also act as indicators, clearly showing what's happening on that pin. When the pin is used as input, you can clearly see whether the signal is received by just looking at changes on the LEDs. The pre-soldered header pins come with nice labels. This helps user to easily connect inputs and outputs to the right pins. This will further assist them in interfacing with sensors and actuators.
• Simplify proper shutdown using push button. You can easily follow the steps and choose one of the push button as the power button to properly shutdown the Raspberry Pi. Just press the button and it will shut down.

Maker pHAT for Raspberry Pi Maker pHAT is designed to be the same size as Raspberry Pi Zero board, it stacks perfectly on top of Rpi Zero with the four mounting holes aligned. (What is a HAT? Read this to know more) We do advise getting Raspberry Pi Zero WH (pre-solder header pin) for beginner because it is not an easy work to solder the 40-pin GPIO, not to forget you need to have the soldering tools too. https://s3-ap-southeast-1.amazonaws.com/cdn.cytron.io/HAT-MAKER/Maker+pHAT+RpiZero.gif Maker pHAT is also compatible with Raspberry Pi 3B, 3B+ or even the latest Raspberry Pi 3A+, just need to insert the 2x20 stacking header(included), as photo shows:

Maker pHAT is compatible with:

• Raspberry Pi Zero V1.3 (will need to solder 2x20 header pin)

• Raspberry Pi Zero W (will need to solder 2x20 header pin)

• Raspberry Pi Zero WH (Ready for plug and use)

• Raspberry Pi 1 Model A+ (Will need 2x20 stacking header)

• Raspberry Pi 3 Model A+ (Will need 2x20 stacking header)

• Raspberry Pi 3 Model B (Will need 2x20 stacking header)

• Raspberry Pi 3 Model B+ (Will need 2x20 stacking header)

Documents/Tutorials: - User's Manual - Schematic (pdf) - Sample Python Code (github)

Packing List: - 1 x Maker pHAT - 1 x 2x20 Stacking Header