little groovebox with 4 sounds and step sequencer
Designed by JanCumpelik in CzechiaNo shipping info available.
Set destination country to see options
Shipping to starts at
Free shipping is available to !
Ships from
This item does not ship to .
More Info
Sign up to get notified when this product is back in stock!
Lunchbeat - 1bit groovebox DIY KIT Lunchbeat is opensource groovemachine with 8 step sequencer and four 1bit sounds. (please note that video shows two prototypes with homemade PCBs. final version of …
Read More…Lunchbeat is opensource groovemachine with 8 step sequencer and four 1bit sounds.
(please note that video shows two prototypes with homemade PCBs. final version of DIY kit contains professionaly manufactured PCBs from PCB company, as seen on photographs :) thank you for your consideration)
START/STOP - runs or stops sequencer. When sequencer is started in external sync mode, it waits for first TRIG in pulse. In SETUP mode this button selects internal or external clock. EDIT - cycles thru all sequencer steps from step 1 to step 8, I call this EDIT mode. Selected step is marked with fully light LED. SOUND BUTTONS - in EDIT mode you turn on/off sounds to be played on selected step. When not in EDIT mode, sounds can pe played by pressing sound button at any time. In SETUP sound buttons are used to enter TRIG division value. In binary! :) MOD POTS - each sound has dedicated potentiometer to tweak sound parameters in real time. TEMPO POT - tempo of internal clock generator.
Lunchbeat can be switched to internal clock, so sequencer advances in intervals given by internal clock generator, and so Lunchbeat sends short 5V pulses to TRIG connector, serving as master. Or Lunchbeat can be switched to external clock, receiving clock via TRIG cable, and sequencer advances when rising edge of 5V pulse is received. Holding EDIT button for longer time gets Lunchbeat to setup mode (tempo LED flashes rapidly). In setup mode you can select internal or external clock and division factor of TRIG synchronization. With division factor set Lunchbeate is receiving (or sending) every x-th TRIG pulse. Division factor "x" can be any number from 1 to 15. Can be used for creating unequal floating beats. Leave setup mode by holding EDIT button for longer time again. WARNING: there is no protection circuitry on TRIG IN input! So be sure your TRIG signal does not exceed 5V! In other case you can fry your chip.
MCU RESET - mcu reset button is not usually implemented on music instrument. But my assumption is that user will be messing with firmware, so there we go. Rigid 2.5N pushutton is used, to prevent reseting unit accidentaly. ISP6pin - hacker's gate to unit's microcontroller. Tweak the sound algorithms. Tweak the sequencer. Change unit's purpose completely. Use the fact that Lunchbeat is the same thing as Arduino with 6 buttons, 5 pots, 8 LEDs on SPI shift register and 3-bit digital to analog converter. You can run Arduino sketches on it. From here it is up to you and your fantasy.
Microcontroller Atmel Atmega328p is running at freq 16MHz. 6 buttons is connected to digital input pins with enabled internal pullup resistors, and five potentiometers connected to analog input pins. Audio is outputed thru 3-bit resistor-2-resistor digital/analog converter with LM358n operational amplifier in voltage follower mode and DC blocking capacitor. 8 blue LEDs are controlled with 74595 shift register, to which data is sended from MCU via SPI bus. Internal sampling frequency is 15626Hz. So there is interrupt routine firing 15626x per second. This routine checks if some sound should be playing, and if so, checks how long is that sound playing already and than is computed value for output. Sounds are 1 bit, so output value can be only 0 or 1, nothing else. After that all four sound values are summed together (mixed) and this final mix value is pushed to 3-bit DAC.
No country selected, please select your country to see shipping options.
No rates are available for shipping to .
Enter your email address if you'd like to be notified when LUNCHBEAT - 1-bit groovebox DIY KIT can be shipped to you:
Thanks! We'll let you know when the seller adds shipping rates for your country.
Shipping Rate | Tracked | Ships From | First Item | Additional Items |
---|---|---|---|---|
:
|
No shipping info available.
Set destination country to see options
Shipping to starts at
Free shipping is available to !
Ships from
This item does not ship to .
More Info
Sign up to get notified when this product is back in stock!
$195.00
Free Shipping!
$199.95
Free Shipping!
$107.98
Free Shipping!
$29.00
Free Shipping!
By clicking Register, you confirm that you accept our Terms & Conditions
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!