USB 3.3V & 5V Serial ProgrammerDesigned by H2O2FromH2O, Ships from United States of America
The H2O2-USB CH330N is a USB to Serial bridge so moving serial data to and from the Arduino is as simple as connecting RX, TX and GND, to the CPU's UART or Soft Serial port. Use it to have instant and continual access to your programs data, no more swapping from programmer to data output and back again with each update. It utilizes the CH330N, an inexpensive USB to Serial converter, made by WCH Co Ltd.
The design of the H2O2-USB CH330N output connector is fully user selectable. Get the pinout you need in the order you require. Accomplish this by removing the solder on the Solder Bridged pads, and connecting the needed through hole Via to the needed output position with a jumper wire. The default pinout is [ 1:GND | 2:+V | 3:TX | 4:RX | 5:RTS ].
The H2O2-USB CH330N is designed to be compatible with ESP8266, Arduino Pro Mini, a Standalone or your own Bread Board Arduino, even those damaged Arduino Nano, Arduino Duemilanove, Arduino Diecimila, clones with those faulty counterfeit copies marked FTDI can once again be utilized and reprogrammed. If you want a reliable Chip Set that won't maliciously be damage by a simple OS driver update then this is the solution.
Fixed Comport number assignment, Each USB hub's port will be assigned a different comport number. This number can be changed within the Windows environment.
There are two red LED's indicating activity for RX and TX. They will blink when data is present. The Power indicator is Green and is on when the 3.3V or 5V jumper is selected.
I had a need for a small USB serial programmer/data port. That was also versatile and functioned on AVR/Arduino CPU's.
Hey DIY'ers, make this project on your own. Get Just the board from here, and add your own parts.
Open Source Hardware and Software
Designed to be used for USB to TTL electronic projects.
Simple to interface with MCU.
TTL interface output, easy to connect to your MCU.
Compatible With Arduino IDE.
Work with 3.3V and 5V target devices,
Selectable Power for 3.3V or 5V target devices with UART logic level control signals to match selected voltage.
Provides up to 475mA output current at 5V and 250mA at 3.3V.
Drivers: Android Host 3.1 and above USB Host mode.
Output is 5-pin interface:(GND / VCC / TXD / RXD / RTS)
Supports Special non-standard Baud Rates like 74880 on ESP8266's Bootloader, 56000, 57600 and 76800 used by some boot loaders when uploading software
This board is sold ASSEMBLED as shown, WITHOUT pin header Soldered.
Half the Price of Similar Modules
16mm x 53mm, 0.62" x 2.1" - With USB Connector and Board
16mm x 38mm, 0.62" x 1.5" - With Board
◈ 1x H2O2-USB CH330N 3.3V & 5V-TTL Serial, Assembled and Tested With Optional Parts and or Services as Ordered. Note: The 5 pin Programming Headers is not normally soldered; Option.
CH330N Drivers: Its called CH341SER and is direct from www.wch.cn
◉ Windows driver. ◎ Driver home Page
◉ Android APP. ◎ Driver home Page
◉ Mac driver. ◎ Driver home Page
◉ Linux driver. ◎ Driver home Page
Most serial terminals.
Putty R 0.66 or Higher
Arduino IDE Serial Terminal
The schematic in PDF Format is Here.
We recognize our top users by making them a Tindarian. Tindarians have access to secret & unreleased features.
We look for the most active & best members of the Tindie community, and invite them to join. There isn't a selection process or form to fill out. The only way to become a Tindarian is by being a nice & active member of the Tindie community!